我就是想知道yocto 3.14.x 生成的uboot如何更新到开发板上去，我现在用的还是那个2009的uboot，一直都是 ...
用 2009 的 uboot 挂载 nfs 的 rootfs ，系统启动以后， 直接将 rootfs 中新的 uboot dd 到 mmcblk0root0 里面 seek=2 就行。 或者永 mfg 也是可以烧写的。 哥们有没有升级成功啊！ ！！！ 官方支持升级吗？ 请问，网卡搞定了么？ whyfy 发表于 2016-8-12 21:18
请问，网卡搞定了么？
FEC 本来就好用啊。 scaborough 发表于 2016-8-27 16:44
FEC 本来就好用啊。
额，是飞凌的板子么？我的不好用呢？而且直接用你提供的patch编译的内核也无法PING通PC，感觉像是自动协商的问题。
[ 4.305861] fec 2188000.ethernet eth0: Freescale FEC PHY driver (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
[ 4.323087] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.895234] fec 2188000.ethernet eth0: Freescale FEC PHY driver (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
[ 4.895354] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.924713] libphy: 2188000.ethernet:01 - Link is Up - 100/Full
[ 19.930733] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 31.954476] libphy: 2188000.ethernet:01 - Link is Down
[ 31.994277] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 50.998712] libphy: 2188000.ethernet:01 - Link is Up - 100/Full
[ 51.005121] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 67.038544] libphy: 2188000.ethernet:01 - Link is Down
[ 67.078555] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 86.082709] libphy: 2188000.ethernet:01 - Link is Up - 100/Full
[ 86.089082] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 88.094492] libphy: 2188000.ethernet:01 - Link is Down
[ 88.133949] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
libphy: 2188000.ethernet:01 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
libphy: 2188000.ethernet:01 - Link is Down
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
libphy: 2188000.ethernet:01 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready 可以提供你的linux3.14的内核和uboot源码吗 3.0.35不支持设备树，作者现在研究的怎么样了，能否写一篇教程普及一下3.14如何移植？
页:
1
[2]